Configure Bitstream Passthrough for Plex Audio

Published 2026-10-16 · PlexBeam

Bitstream passthrough sends the raw audio data from a media file directly through the Plex client and HDMI connection to your AV receiver or soundbar. The receiver decodes the audio — not the Plex client, not the server. This is the only way to deliver lossless audio formats (Dolby TrueHD, DTS-HD Master Audio) and object-based formats (Dolby Atmos, DTS:X) with full quality. When bitstream passthrough is not configured correctly, Plex either decodes the audio to PCM (losing lossless advantages and spatial metadata) or transcodes it on the server (wasting resources and degrading quality). This guide covers the complete bitstream passthrough configuration chain.

What Bitstream Passthrough Actually Does

In normal audio playback, the Plex client decodes the audio track and sends uncompressed PCM audio to the output device. The receiver receives a decoded signal — it does not know what the original format was.

With bitstream passthrough, the client wraps the compressed audio data in an HDMI audio packet and sends it untouched to the receiver. The receiver identifies the format (TrueHD, DTS-HD MA, EAC3, etc.) from the bitstream header and decodes it using its own hardware. This matters because:

  • Lossless preservation: TrueHD and DTS-HD MA are lossless — decoded to PCM they produce identical output. But the receiver's DACs (digital-to-analog converters) and processing may differ from the client's. Letting the receiver handle the full decode chain gives you the receiver manufacturer's intended audio quality.
  • Spatial metadata: Dolby Atmos and DTS:X spatial metadata exists only in the compressed bitstream. Decoding to PCM strips the object-based positioning — the receiver gets channel-based audio instead of spatial audio. Bitstream passthrough is the only way to deliver Atmos and DTS:X.
  • Receiver processing: Many receivers apply room correction (Audyssey, Dirac, YPAO) to the decoded audio. Some room correction features work differently or better with bitstream input than PCM input.

HDMI Configuration

Client to Receiver (Direct Connection)

The most reliable passthrough setup: connect the Plex client device directly to an HDMI input on the receiver, then connect the receiver's HDMI output to the TV. The client sends the bitstream to the receiver, and the receiver passes video through to the TV.

On the receiver, check these settings per HDMI input:

  • Enhanced HDMI / 4K Signal Format: Enable this on the input connected to the Plex client. Some receivers label this Enhanced, 8K Enhanced, or 4K Enhanced. Without it, the input may not accept high-bandwidth audio bitstreams.
  • Audio mode: Ensure the input is not set to Analog or PCM-only mode. It should be in Auto or Bitstream mode.

Client to TV to Receiver (ARC/eARC)

When the client connects to the TV first:

  • Standard ARC: Limited to Dolby Digital and DTS compressed bitstreams. No lossless formats, no Atmos. If this is your only option, your maximum quality is lossy 5.1.
  • eARC: Supports all bitstream formats including TrueHD Atmos and DTS:X. Both TV and receiver must have eARC-capable HDMI ports (usually labeled eARC), and eARC must be enabled in both devices' settings.

Even with eARC, the direct-to-receiver connection is more reliable. eARC adds another link in the chain where handshake failures can occur.

TV Audio Settings

When using ARC or eARC, the TV's audio output setting must be configured to pass bitstream audio:

  • Set the TV's audio output to Passthrough, Bitstream, or Auto (not PCM).
  • Some TVs have an additional setting for eARC — ensure it is enabled.
  • Disable any TV audio processing (volume leveling, dialogue enhancement) as these may interfere with bitstream output.

Plex Client Configuration

Enable Passthrough

In the Plex client app, navigate to Settings, then Audio (or Advanced Audio settings). Enable the master passthrough toggle — it may be labeled Allow Passthrough, Audio Passthrough, or Bitstream.

Enable Individual Codecs

After enabling passthrough, you must enable each codec individually:

  • Dolby Digital (AC3): Enable. Supported by virtually every receiver.
  • DTS: Enable if your receiver supports DTS. Most do — but verify on the receiver's spec sheet.
  • Dolby Digital Plus (EAC3): Enable. Required for streaming-quality Atmos (EAC3-JOC).
  • Dolby TrueHD: Enable only if your client device and HDMI chain support it. Enabling this on a device that cannot passthrough TrueHD causes silence during playback.
  • DTS-HD: Enable only if supported by both client and receiver. Covers DTS-HD Master Audio and DTS:X.

Only enable codecs your hardware chain actually supports. Enabling an unsupported codec does not cause a graceful fallback on all clients — some clients send garbage data or produce silence.

Quality Setting

Set playback quality to Original or Maximum. Any quality reduction forces the server to transcode, which re-encodes the audio and destroys the original bitstream.

Server-Side Settings

The Plex server should not touch the audio stream when passthrough is working:

  • Audio Boost: Disable or set to none. Audio boost applies server-side gain which requires decoding and re-encoding the audio.
  • Remote streaming bitrate: Set high enough that the full audio track passes through without restriction. Low bitrate caps can trigger audio transcoding even when the client supports passthrough.

Verifying Bitstream Passthrough

Receiver Display

The definitive verification method. During playback, your receiver's front panel or on-screen display shows the detected audio format:

Display ShowsMeaning
Dolby AtmosTrueHD or EAC3 Atmos bitstream received and decoded
Dolby TrueHDLossless TrueHD bitstream (without Atmos metadata)
Dolby DigitalLossy AC3 bitstream — passthrough working but at lossy quality
DTS-HD MA or DTS:XLossless DTS bitstream received and decoded
DTSLossy DTS core — lossless extension not passing through
PCM or Multi Ch PCMClient decoded the audio and sent PCM — passthrough NOT working
Stereo or 2.0Either the source is stereo or surround passthrough failed completely

Plex Dashboard

Check the Now Playing panel during playback. Audio should show Direct Play. If it shows Transcode or Direct Stream for audio, the server is processing the audio before sending it — the original bitstream is not being preserved.

Troubleshooting

Receiver Shows PCM Instead of Expected Format

  • Passthrough is not enabled in the Plex client. Check Settings, Audio.
  • The specific codec is not enabled. You need both the master passthrough toggle AND each individual codec enabled.
  • The client device does not support passthrough for that format. Check the device specifications — many streaming sticks cannot pass through TrueHD or DTS-HD.

No Audio at All When Passthrough Is Enabled

  • The receiver does not support the codec being sent. Temporarily disable passthrough — if audio plays (as PCM), the bitstream format is the issue.
  • The HDMI cable may not support the bandwidth. Try a different premium high-speed HDMI cable.
  • Enhanced HDMI mode may need to be enabled on the receiver input.

Audio Plays But Receiver Shows Wrong Format

  • The file may contain a different codec than expected. Check the file's audio track details in Plex or MediaInfo.
  • When a file has multiple audio tracks, Plex may be selecting a different track than the one you expect. Set the preferred audio track in playback settings during playback.
  • If using eARC and the receiver shows Dolby Digital instead of TrueHD, eARC may not be properly negotiated. Check eARC settings on both TV and receiver, and try power-cycling the entire chain.

Bitstream Works for Some Files But Not Others

  • Different files may contain different audio codecs. A movie with TrueHD audio passes through on a Shield Pro but a movie with DTS-HD MA requires DTS-HD passthrough to be separately enabled.
  • Some files have only one audio track in an unsupported format. Plex must transcode because there is no compatible fallback track. Adding a compatible secondary audio track to these files avoids the problem.
← Back to Blog
More from LuxuriousComputers: LuxuriousComputers · Computer Repair · Remote Fix · Phone Repair · HVAC · Plex Support